Stapler installation tutorial | HUISHENG

Office stapler is a common office equipment in our daily life, but there may be small white is not clear how stapler and binding machine is installed and used.Today xiaobian carefully for you to collect the stapler and binding machine installation and use methods, xiaobian below for you to introduce, everyone office talent to look at it!

A simple desktop stapler using the door method

1. Turn on the stapler

2, it is better to use a hand to secure the open end, to prevent ricochet injury hand

3. Put in the staples

4, put away

5. Close

6. Aim at the place where the staple should be fixed

7. Press down hard with the palm of your hand

8, set, let go of the stapler

9. OK!

Matters needing attention

Be careful not to nail your finger!

Two, manual binding machine use method

Although many enterprises are now update the machine, binding machine also largely replaced by automatic binding machine, but there are still many users still users to dynamic binding machine, in the process of using manual binding machine users tend to have some problems, I give you the following simple about the use of the manual binding machine.

1. The handle shall be installed first, and the handle prepared with the box shall be set into the position of the square axis on the right side of the binding machine and screwed tight. Read the manual carefully before binding, and consider the amount of binding paper.

2. Adjust the paper margins by adjusting the scale with the adjusting screw (installed behind the binding machine).In the adjustment of the diameter of the pull ring, the paper margin, the diameter of the pull ring, the paper margin.You can adjust the appropriate paper margins according to their own needs.

3. After putting the paper in place, we need to punch holes in the paper, tidy the paper and press it close to the positioning block, then send the paper into the machine in parallel. Until the top is in place, press the paper with the left hand, hold the handle with the right hand, press down until the blade penetrates the paper, and then lift the handle.

4. Before binding, we need to put the needle on the machine. First, loosen the fixing screw on the pin holder, remove the pin holder, attach the hook at the end of the pin holder to the pin holder hole, keep it vertical, then put the pin holder into the pin holder in place, and finally tighten the fixing screw on the pin holder.

5, to the last step, binding, the presser foot first rises the handwheel clockwise rotation presser foot, the binding material into the press foot, put the paper in, let go of the presser foot wheel pressure automatically, then the presser foot wheel to rotate counterclockwise around 180 ° after lock, needle handle counterclockwise to put order, order the needle through the material.Wait until the lead arm automatically hangs the thread in the pin hook slot, then you can lift the handle up. When the pin exits, the binding thread will be locked, and then release the pressure foot handwheel in a clockwise direction. Then you can finish the stitch binding.

Three, standard stapler use method

1. Mounting handle: set the handle prepared with the box into the position of the square axis on the right side of the binding machine (note: working Angle of the handle) and tighten it with the lock screw.

2. Paper consumption: the paper consumption must be determined according to the specifications of each machine, not excessive.Otherwise, the following undesirable situations may occur:

(1) handle pressure, through the paper barrier, unable to penetrate.

(2) the margin is not balanced, easy to produce the paper edge roll.

(3) cause the distortion of the square axis, resulting in shortened service life of the binding machine.

3, the paper margin adjustment, the principle is: according to the diameter of the pull ring to determine the size of the margin.The method is to use the adjusting screw (installed behind the binding machine) to adjust the scale to achieve the purpose of margin.The rule is: the diameter of the pull ring, the paper margin is large, the diameter of the pull ring is small, the paper margin is small.

4, punch operation method: tidy up the paper, close to the positioning block, parallel paper into the machine, until the top in place.Press the paper with the left hand, hold the handle with the right hand, press down until the blade penetrates the paper, then lift the handle.(3) smooth hands will play good paper out, such as the phenomenon of hanging paper, repeatedly press down the handle, and then up to the position can take out the paper.

5, pull ring binding method: according to the number of paper, choose different sizes of pull ring, slowly push the handle up to the pull ring to open, then insert the paper hole into the pull ring, slowly pull the handle back, let the pull ring teeth all inserted into the paper hole, pull the handle in place, tighten the pull ring mouth, the binding book is ready.

Read the above introduction, we should understand the stapler installation is how one and the same, we must pay attention in the process of operation must not set to the finger, or be careful.

Today about the stapler installation to introduce to you here, want to learn more about the relevant information please continue to pay attention to HUISHENG stapler factory!


Post time: Jan-13-2020
WhatsApp Online Chat !